, .

PS90 Gen 1 Hammer Only – Short Pull Drop-in Upgrade for Your Trigger Pack

$129.00

PS90 Gen 1 Hammer V2 – Short Pull Drop-in Upgrade from Man Kave Specialties

New Enhancements to the finish and friction surfaces make this the best PS90 hammer ever!

ps90 gen 1 hammer

PS90 Gen 1 Hammer Reduces Trigger Pull by over 35% and Felt Trigger Weight by over 15%

PS90 Gen 1 Hammer Short Pull is compatible with any Gen trigger pack and its easy install makes it a must have upgrade for your PS90. The PS90 Gen 1 Hammer is first machined from solid billet 7075-T6 Aluminum, then mil 8625 hard coat anodized, and finally Teflon coated to make it as smooth as possible to assist in the smooth function of the trigger assembly. The hammer is modeled from the Gen 1 hammer, which has the front sear notch in the original Gen 1 position. FN has changed the design of the hammer and trigger pack over the years to make it harder for people modify the trigger pack to make the rifle into an illegal full auto rifle which is a serious crime under the NFA. The PS90 Gen 1 Hammer allows you to install a higher quality, original design Gen 1 Hammer into your existing trigger pack to replace the cheap plastic hammer with a nice billet Aluminum PS90 Gen 1 Hammer.

The Benefits of swapping out the original plastic hammer from your trigger pack are three-fold:

  1. The PS90 Gen 1 Hammer reduces trigger pull length by over 35%
  2. The PS90 Gen 1 Hammer reduces felt trigger weight by over 15%
  3. The PS90 Gen 1 Hammer weighs slightly more than its plastic counterpart, allowing each strike of the hammer to impact the firing pin harder causing harder primer strikes.

This installation requires no permanent modification. The installation takes about 5-10 minutes and requires only simple tools such as a punch or thin bar to push out the trigger pack pins that hold in the existing hammer. Make sure you take a look at how the original hammer is set in the trigger pack and how it operates so you can get a good idea of how the new PS90 Gen 1 Hammer should be installed.

Also available at FNspecialties.com

#1 in FN Pistols, Rifles and Accessories

Out of stock

PS90 Gen 1 Hammer – Short Pull Drop-in Upgradeps90 gen 1 hammerPS90 Gen 1 Hammer Reduces Trigger Pull by over 35% and Felt Trigger Weight by over 15%

PS90 Gen 1 Hammer Short Pull is compatible with any Gen trigger pack and its easy install makes it a must have upgrade for your PS90. The PS90 Gen 1 Hammer is first machined from solid billet 7075-T6 Aluminum, then mil 8625 hard coat anodized, and finally Teflon coated to make it as smooth as possible to assist in the smooth function of the trigger assembly. The hammer is modeled from the Gen 1 hammer, which has the front sear notch in the original Gen 1 position. FN has changed the design of the hammer and trigger pack over the years to make it harder for people modify the trigger pack to make the rifle into an illegal full auto rifle which is a serious crime under the NFA. The PS90 Gen 1 Hammer allows you to install a higher quality, original design Gen 1 Hammer into your existing trigger pack to replace the cheap plastic hammer with a nice billet Aluminum PS90 Gen 1 Hammer.

The Benefits of swapping out the original plastic hammer from your trigger pack are three-fold:

  1. The PS90 Gen 1 Hammer reduces trigger pull length by over 35%
  2. The PS90 Gen 1 Hammer reduces felt trigger weight by over 15%
  3. The PS90 Gen 1 Hammer weighs slightly more than its plastic counterpart, allowing each strike of the hammer to impact the firing pin harder causing harder primer strikes.

This installation requires no permanent modification. The installation takes about 5-10 minutes and requires only simple tools such as a punch or thin bar to push out the trigger pack pins that hold in the existing hammer. Make sure you take a look at how the original hammer is set in the trigger pack and how it operates so you can get a good idea of how the new PS90 Gen 1 Hammer should be installed.

%d bloggers like this: